Skip to product information
1 of 1

SIKA Sikadur-130 Normal Epoxy Mortar 30kg

SIKA Sikadur-130 Normal Epoxy Mortar 30kg

Regular price 7.485,00 Kč
Regular price Sale price 7.485,00 Kč
Unit price 249,50 Kč/kg
Sale Sold out
Taxes included. Shipping calculated at checkout.
EMPTY DOM REMOVE PROTECTOR
Quantity
EMPTY DOM REMOVE PROTECTOR

SIKA Sikadur-130 Normal 30 kg – 2-component epoxy mortar for bonding, repairing & filling

Sikadur-130 Normal is a 2-component, moisture-tolerant and thixotropic epoxy resin mortar with special fillers. It is used as a bonding mortar, repair mortar, and filling mortar and adheres to concrete even on matte-damp surfaces – without a primer.

Thanks to its non-sag consistency, Sikadur-130 can also be applied to vertical surfaces and overhead. It cures without shrinkage and achieves very high bond and compressive strengths. The two components are differently colored (white and dark gray), so you can immediately see when the material is homogeneous while mixing.

Scope of delivery: 30 kg container, not pre-dosed – Component A 20 kg + Component B 10 kg. Color when mixed: concrete gray.

Advantages of Sikadur-130

  • No primer required on concrete and mortar
  • Adheres to dry and matte-damp concrete
  • Non-sag on vertical surfaces and overhead
  • Shrinkage-free curing
  • Very high bond strength (> 4.0 MPa, concrete failure)
  • High initial and final strength
  • High abrasion and impact resistance
  • Liquid-tight and good chemical resistance
  • Different colored components for reliable mix control
  • CE-marked according to EN 1504-4

Typical application areas

As a bonding mortar and structural adhesive for precast concrete elements, hard natural stones, ceramics, fiber cement, mortar, brick, and masonry as well as steel, iron, aluminum, wood, polyester, epoxy, and glass.

As a repair mortar for:

  • Edges and corners
  • Holes and voids
  • Vertical surfaces and overhead repairs

As a filling and smoothing compound for joints, crack edges, blowholes, and spalling.

Technical data

  • Mixing ratio: A : B = 2 : 1 (by weight or volume)
  • Density: approx. 1.70 kg/l (mixed, +23 °C)
  • Compressive strength after 7 days: 55–65 MPa (+23 °C)
  • Flexural strength after 7 days: > 20 MPa
  • Bond strength: > 4.0 MPa (concrete failure)
  • Layer thickness: max. 30 mm per application, non-sag on vertical surfaces up to 15 mm
  • Application temperature: +8 °C to +30 °C (material, air, and substrate)
  • Pot life (200 g): approx. 145 min at +10 °C, approx. 55 min at +20 °C, approx. 35 min at +30 °C
  • Shelf life: 24 months from production, store dry at +5 °C to +30 °C

Consumption

Consumption is approx. 1.70 kg/m² per mm of layer thickness and depends on the roughness of the substrate. A 30 kg container is therefore sufficient, for example, for approx. 17 m² at 1 mm layer thickness or approx. 3.5 m² at 5 mm.

Application of Sikadur-130

1. Preparing the substrate

Concrete and mortar must be at least 28 days old, sound, clean, and free of oil, grease, and dust (pull-off strength min. 1.5 MPa). Remove cement laitance, e.g., by grinding or sandblasting. Derust steel to cleanliness grade SA 2.5. Polyester, epoxy, glass, and ceramics must be free of grease and oil and primed wet-on-wet according to the manufacturer; highly absorbent substrates should also be pre-treated. The substrate may be dry or matte-damp, but must not have any standing water.

2. Mixing

Since the 30 kg container is not pre-dosed, weigh out the components in a 2 : 1 ratio. Do not mix individual batches larger than 6 kg and mix homogeneously for at least 3 minutes using a low-speed mixer (max. 300 rpm), e.g., in a mixing bucket. Then transfer to a clean container and mix briefly once more. Only mix as much material as can be used within the pot life.

3. Application

Apply the material with a spatula, trowel, or smoothing trowel, e.g., with a finishing trowel. Work well into matte-damp substrates. For edge repairs, formwork is recommended. For manual application, protective gloves are mandatory.

4. Curing

Fix bonded metal profiles on vertical surfaces for at least 12 hours (at +20 °C). The substrate temperature must be at least 3 °C above the dew point during application and curing.

5. Cleaning tools

Clean tools immediately after use. Cured material can only be removed mechanically.

Note: All information is taken from the manufacturer's technical data sheet. Before processing, please observe the current product and safety data sheet, which can be downloaded at the bottom of this page.

Manufacturer's specifications

View full details

FAQ

How long does shipping take?

Your order will typically be shipped within three to five business days. In rare cases, however, there may be slight delays. If this happens, our service team will inform you immediately!

How much are the shipping costs?

A detailed overview of shipping costs can be found HERE . These are calculated at checkout and vary depending on the product, weight, and delivery address.

Can I pick up my order myself?

Yes, you can select the "Collection" delivery option at checkout. We will inform you by email as soon as your order is in stock and ready for collection. Our regular collection times are Monday to Friday from 2 pm to 4 pm .

Can I also get specific advice on a product?

Yes, of course! Feel free to contact our in-house expert HERE !

Can I register as a business customer?

Yes! As a business customer, you can request special access HERE via our registration form . With this access, you'll benefit from net prices , attractive discounts on selected product groups , and individual pricing for bulk orders.